|
|
DM1810-916MB
 |
Not for new design
916.50 MHz Transceiver Module
|
Click here if you need additional technical information,
to inquire about samples or to discuss your custom needs.
• Base Station with Host Serial Interface
• Compatible with RFM miniMESHTM Network Protocol
• 3 V, Very Low Current Operation
• Ready-to-Use OEM Module
Click here if you need additional technical information,
to inquire about samples or to discuss your custom needs.
 download product manual
|
- Features
- Specs
- AppNotes
- Dev Kit
- Buy Now
- End of Life
| The DM1810-916MB is the 916.50 MHz base station module in the DM1810 family of RF transceiv-
ers. The DM1810 family is designed for adding wireless mesh network connectivity to a wide range
of monitoring and control systems. The DM1810-916MB is equipped with a serial I/O port to interface
a host microcontroller. Radio communications range in an “open field” environment is typically
600 meters/hop. The DM1810-916MB combines RFM’s very low current ASH radio technology with
low power microcontroller technology to achieve long battery life. This module is compatible with
RFM miniMESHTM network protocol, which provides “plug-and-play” multicast mesh network routing.
The DM1810-916MB is certified for operation under FCC 15.247 and Canadian RSS 210
regulations. |
|
|
|
|
Electrical Characteristics |
| Characteristic |
Symbol |
Minimum |
Typical |
Maximum |
Units |
| Operating Frequency |
fO |
916.30 |
|
916.70 |
MHz |
| Modulation Type |
|
|
OOK on BPSK Spreading Code |
|
|
| RF Encoded Data Transmission Rate |
|
|
4.8 |
|
kb/s |
| Average Receive Input Current, No External Power Supply Load |
IR |
|
5.5 |
|
mA |
| Receiver Input Signal for 10-3 BER, 25 °C |
|
|
-100 |
|
dBm |
| Average Transmit Input Current, No External Power Supply Load |
ITA |
|
15.75 |
|
mA |
| Peak Transmit Input Current, No External Power Supply Load |
ITP |
|
|
32 |
mA |
| Peak Transmitter Output Power |
PO |
|
10 |
|
mW |
| Bind Input and Serial RX Logic High |
|
2.4 |
|
|
V |
| Bind Input and Serial RX Logic Low |
|
|
|
0.45 |
V |
| Serial TX Logic High |
|
2.4 |
|
|
V |
| Serial TX Logic Low |
|
|
|
0.3 |
V |
| Serial Port Data Rate |
|
|
9.6 |
|
kb/s |
| Average Sleep Input Current, No External Power Supply Load |
ISA |
|
60 |
|
?A |
| Power Supply Input Voltage Range, -40 to +85 oC |
VIN |
3.1 |
|
10 |
V |
| Power Supply Input Voltage Range, 0 to +85 oC |
VIN |
2.6 |
|
10 |
V |
| Regulated Power Supply Output Voltage, VIN 3.1 to 10 V |
VOUT |
|
3.0 |
|
Vdc |
| Regulated Power Supply Voltage Ripple |
|
|
|
10 |
mVP-P |
| Relative Humidity Range, Non-Condensing |
RH |
10 |
|
90 |
% |
|
|
|
| Application Notes
see All Product Application Notes |
AN1800-1 2.3
DM1800 V2.2 and V2.3 Application Programming, provides an overall discussion of application software development for a DM1800 MESH network using V2.2 or V2.3 firmware, plus an example thermistor temperature sensor application. |
AN1800-1 2.4
DM1800 V2.4 Application Programming, provides an overall discussion of application software development for a DM1800 MESH network using V2.4 firmware, plus an example thermistor temperature sensor application. |
AN1800-2
DM1800 Poll, allows users to poll nodes, read and write to digital output and display input and output commands. |
|
|
|
|
|
|
|
|
AN1810-1 2.4
DM1810 V2.4 Application Programming, provides an overall discussion of application software development for a DM1810 MESH network using V2.4 firmware, plus an example thermistor temperature sensor application. |
AN1810-1 2.5
DM1810 V2.5 Application Programming, provides an overall discussion of application software development for a DM1810 MESH network using V2.5 firmware, plus an example thermistor temperature sensor application. |
AN2200-1
DM2200 Temperature Sensor Demonstration |
AN2200-2
DM2200 Sleep Duty Cycle Demonstration |
|
AN2200-4
ZN241G & DM2200 Remote Control Mesh |
ANM1001
A Solar Energy Harvester for Wireless Sensor Networks |
ANM1002
Sizing Solar Energy Harvesters for Wireless Sensor Networks |
|
|
|
|
| |
| Developer Kits |
 |
| The DM1810-915 Development Kits give you a way to get a wireless mesh networking application
at 916 MHz up and running in minutes. Both Development Kits are built around the RFM
DM1810-916 Wireless Modules for embedded low power mesh networking applications. With the
DM1810 Quick Kit you can quickly and easily prototype an embedded wireless mesh networking
solution for your application. With a DM1810 Pro Kit you can fully develop and test a custom
MESH network application.
The DM1810-916 Pro Development Kit contains:
• Five (5) DM1810 Modules configured as field nodes to connect to your product
with serial, analog or digital I/O ports
• One (1) DM1810 Module configured as a base station to connect to a personal
computer over USB
• Three (3) IM1810 Interface Boards that attach to a DM1810 Module and provide
standard connectors to the DM1810’s standard I/O ports.
• Five (5) DM1810 Router Units, which contain a connector for an external power
source (supplied).
• Five (5) Universal World Wide AC Power Adapters to provide external power for
the IM1800 Interface Boards and the DM1810 Router Units.
• Four (4) Battery Packs that can be used to power a IM1810 Interface Board with
a connected DM1810 Module.
• One (1) USB Cable to connect the DM1810 base station module in an IM1800
Interface Board to a PC via USB.
• Quick Start Guide to step you through setting up a working wireless mesh
network application in minutes.
• Development Kit CD that contains detailed specifications, user guide, utilities,
sample programs, application notes, and other documentation. |
|
| RFM Part |
Frequency |
Description |
|
|
|
| Developer Kit containing 1 Base, 3 Routers, 3 Nodes |
|
|
|
|
| Quick Kit 1 Base, 1 Router, 2 Nodes |
|
RFM products are sold through a world-wide network of manufacturer's sales reps and distributors.
| The purpose of this End-of-Life Product Notice is to communicate the obsolescence of this part.
|
|
|
|
Click to Download
